Use Pre-Kote as an undercoat for Toplac or Interlux Super yacht enamels.
Excellent obliteration allows for easy colour changing.
* Range of colours to compliment topcoat
* Easy application and rub down
* Long overcoating times to allow coat-on-coat application
The tough, flexible resins are long lasting, easy to apply and rub down,
giving a smooth base for the finishing coat. Suitable for all primed
wood, steel, alloy or GRP. |
|
|
Colour |
YUB000-Snow White, YUB783-Red, YUG879-Blue/Grey, YUK954-Dark Blue |
|
Finish |
Low sheen |
|
Specific Gravity |
1.5 |
|
Volume Solids |
47% |
|
Typical Shelf Life |
2 yrs |
|
VOC (As Supplied) |
363 g/lt |
|
Unit Size |
750 ml 375 ml (some colours only) 2.5 Lt (some colours only) |
|
|
| |
Drying |
|
5ºC |
15ºC |
23ºC |
35ºC |
|
|
|
Touch Dry [ISO] |
15hrs |
6hrs |
3hrs |
1hrs |
|
Sandable |
48hrs |
30hrs |
24hrs |
24hrs |
| |
Overcoating |
| |
Substrate Temperature |
| |
5ºC |
15ºC |
23ºC |
35ºC |
|
Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
|
Brightside |
36hrs |
4days |
24hrs |
3days |
16hrs |
2days |
4hrs |
1days |
|
Interdeck |
36hrs |
4days |
24hrs |
3days |
16hrs |
2days |
4hrs |
1days |
|
Interlux Super |
36hrs |
4days |
24hrs |
3days |
16hrs |
2days |
4hrs |
1days |
|
Pre-Kote |
36hrs |
4days |
24hrs |
3days |
16hrs |
2days |
4hrs |
1days |
|
Toplac |
36hrs |
4days |
24hrs |
3days |
16hrs |
2days |
4hrs |
1days |
|
|
Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Yacht Line Super Cleaner, rinse
with fresh water and allow to dry. Abrade with 180-220 grade paper.
In Poor Condition: Remove all previous coatings and prime the
substrate.
PRIMING: All preparation for bare substrates is covered on the
appropriate primer datasheet.
BARE WOOD: Prime with Yacht Primer or UCP.
STEEL: Prime with Yacht Primer or Interprotect.
ALUMINIUM: Prime with Etch Primer followed by either Yacht Primer
or Interprotect.
GELCOAT/COMPOSITE: No priming necessary. Wash down with Yacht
Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with
180-220 grade paper.
ALL SUBSTRATES: If any filling is required use the appropriate
product from the Interfill range. |
|
|
|
Method |
Apply 1-2 coats. If maximum overcoating time of previous coating/primer
is exceeded, abrade using 220-320 grade wet or dry paper. Remove dust
with a dust wipe. To give extra depth of colour, Toplac or Interlux
Super enamels may be added to the undercoat. |
|
|
|
Hints |
Mixing Stir well before use.
Thinner YTA800,YTA063 Thinner No.1 (Thinner No.10 for spraying)
Cleaner YTA800 Thinners No.1
Ventilation and Humidity Control Apply in dry, well ventilated
conditions.
Airless Spray Pressure: 180 bar. Tip Size: 1365-1580.
Conventional Spray For conventional spray application, reduce
viscosity using Thinners No. 10 to 20 - 24 seconds, BS4. Pressure: 3-4
bar. Tip Size: 1.4-1.8 mm.
|
|
|
|
Some Important Points |
Substrate temperature should be minimum 5°C/40°F and maximum 35°C/95°F.
Product temperature should be minimum 5°C/40°F and maximum 35°C/95°F.
Ambient temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Do
not use below 5°C. |
|
|
|
Compatibility/Substrates |
Can be applied over all Interfill products. Only overcoat with one-pack
paints. Not suitable for permanently immersed surfaces. |
|
|
|
Number of Coats |
1-2 |
|
|
|
Coverage |
(Theoretical) - 13.33 (m²/lt) |
|
(Practical) - 12.00 (m²/lt) by brush, 8 m²/lt by spray |
|
|
|
Recommended DFT |
35 microns dry by brush
|
|
Recommended WFT |
75 microns wet by brush |
|
|
|
Application Methods |
Brush, Roller, Airless Spray, Conventional Spray |
|
|
Storage |
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Pre-Kote to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Pre-Kote should be kept in securely closed containers during transport
and storage.
|
|
|
|
Safety |
GENERAL: Read the label safety section for Health and Safety
Information, also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Pre-Kote cannot be disposed of through the municipal waste
route or dumped without permit. Disposal of remainders must be arranged
for in consultation with the authorities.
|
|
|
IMPORTANT NOTES |
The information given in this sheet is not intended to be exhaustive.
Any person using the product without first making further written
enquiries as to the suitability of the product for the intended purpose
does so at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
 and
International are registered trademarks of Akzo Nobel. |
|
