The ultimate in varnish performance, specially formulated for oily wood
types, combining excellent chemical and abrasion resistance with superb
gloss.
* Chemical cure gives resistance to fuels, oil and mild acids and
alkalis
* Up to four times longer service life than ordinary varnishes |
|
|
Colour |
YVA856-Clear |
|
Finish |
Full gloss |
|
Specific Gravity |
1.06 |
|
Volume Solids |
54% |
|
Mix Ratio |
5:2 by volume (as supplied) , Converter/Curing Agent - YVA851 |
|
Typical Shelf Life |
2 yrs |
|
VOC (As Supplied) |
422 g/lt |
|
Unit Size |
750 ml |
|
|
| |
Drying |
|
5ºC |
15ºC |
23ºC |
35ºC |
|
|
|
Touch Dry [ISO] |
7hrs |
5hrs |
2hrs |
1hrs |
|
Pot Life |
5hrs |
3hrs |
2hrs |
1hrs |
| |
Overcoating |
| |
Substrate Temperature |
| |
5ºC |
15ºC |
23ºC |
35ºC |
|
Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
|
Perfection Varnish |
24hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
Perfection Varnish for Teak |
24hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
Schooner |
36hrs |
1mths |
16hrs |
1mths |
12hrs |
1mths |
8hrs |
1mths |
|
Schooner (YVA084) |
36hrs |
1mths |
16hrs |
1mths |
12hrs |
1mths |
8hrs |
1mths |
|
|
Note:If maximum overcoating times are exceeded, sand using
280-320 grade (grit) wet or dry paper. Perfection Varnish for Teak must
be sanded with 320-400 grade paper (and dust removed) prior to
overcoating with Schooner. |
|
Preparation |
PREVIOUSLY VARNISHED WOOD:
In Good Condition: Clean with Yacht Line Super Cleaner. Sand
smooth with 280-320 grade paper. Remove sanding dust with thinners.
In Poor Condition: Remove all previous coatings.
BARE WOOD: Sand smooth with 80-180 grade paper and then 280 grade
paper. Remove sanding dust by brushing, dusting and wiping. If wiping
with solvent then allow to dry completely before applying the first
coat.
Priming bare wood:: Thin the first coat by 20%. |
|
|
|
Method |
For best results when applying by roller, smooth off with a pad or
brush. Performance will be further enhanced if top coated with 2 coats
of Perfection Varnish. If using as a primer on flexible constructions,
apply one coat only under Original. Avoid using direct from the can. |
|
|
|
Hints |
Mixing Stir individual products prior to mixing. Add Curing Agent
to the Base, stir and leave for 10 minutes to allow bubbles to disperse.
Mix the amount you expect to use in a separate container.
Thinner YTA006 Thinners No.9
Cleaner YTA006 Thinners No.9
Ventilation and Humidity Control Apply 4 coats minimum in dry,
well ventilated conditions. Best applied at ambient temperatures of
between 15°C and 20°C. Sensitive to moisture during application. Avoid
excessively humid conditions, over 80% relative humidity. Avoid applying
late in the evening as condensation can cause a loss of gloss overnight.
|
|
|
|
Some Important Points |
Avoid painting in direct sunlight. Avoid humid conditions. DO NOT SPRAY.
Contains Isocyanates which may be harmful to lungs, read the safety data
section before use. Do not use unless mixed thoroughly with the curing
agent at specified ratio. Do not use on light-coloured wood as it will
darken on exposure. Not suitable for continuous immersion. Product
temperature should be minimum 15°C and maximum 35°C. Substrate
temperature should be minimum 5°C/40°F and maximum 35°C/95°F. |
|
|
|
Compatibility/Substrates |
Use only on oily timbers such as Teak. Do not use Perfection Varnish for
Teak on flexible constructions. It should not be used over any one pack
products. |
|
|
|
Number of Coats |
4 coats minimum |
|
|
|
Coverage |
(Theoretical) - 18.18 (m²/lt) |
|
(Practical) - 16.00 (m²/lt)
|
|
|
|
Recommended DFT |
30 microns dry by brush
|
|
Recommended WFT |
55 microns wet by brush |
|
|
|
Application Methods |
Brush, Roller |
|
|
Storage |
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Perfection Varnish for Teak to be realised ensure
that between use the container is firmly closed and the temperature is
between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection Varnish for Teak should be kept in securely closed containers
during transport and storage.
|
|
|
|
Safety |
GENERAL: Read the label safety section for Health and Safety
Information, also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Perfection Varnish for Teak cannot be disposed of through
the municipal waste route or dumped without permit. Disposal of
remainders must be arranged for in consultation with the authorities.
|
|
|
IMPORTANT NOTES |
The information given in this sheet is not intended to be exhaustive.
Any person using the product without first making further written
enquiries as to the suitability of the product for the intended purpose
does so at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
 and
International are registered trademarks of Akzo Nobel. |
|
