Perfection Undercoat is the ideal base for a long lasting scheme, when
used with Perfection finish. The 2-component formulation has excellent
obliteration.
* Long overcoating times to allow coat-on-coat application
* Easy application
Rubs down to an exceptionally smooth finish and the semi-gloss finish
allows easy checking for hull fairness. |
|
|
Colour |
YRA003-White 001, YRA302-Blue 302, YRA603-Dark Grey 603 |
|
Finish |
Semi-gloss |
|
Specific Gravity |
1.39 |
|
Volume Solids |
50% |
|
Mix Ratio |
3:1 by volume , Converter/Curing Agent - YGA006 |
|
Typical Shelf Life |
2 yrs |
|
VOC (As Supplied) |
488 g/lt |
|
Unit Size |
750 ml |
|
|
| |
Drying |
|
5ºC |
15ºC |
23ºC |
35ºC |
|
|
|
Touch Dry [ISO] |
11hrs |
7hrs |
3hrs |
2hrs |
|
Sandable |
48hrs |
30hrs |
16hrs |
12hrs |
|
Pot Life |
5hrs |
3hrs |
2hrs |
1hrs |
| |
Overcoating |
| |
Substrate Temperature |
| |
5ºC |
15ºC |
23ºC |
35ºC |
|
Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
|
Perfection |
32hrs |
4days |
16hrs |
3days |
10hrs |
2days |
8hrs |
1days |
|
Perfection (Eu) |
32hrs |
4days |
16hrs |
3days |
10hrs |
2days |
8hrs |
1days |
|
Perfection Undercoat |
32hrs |
4days |
16hrs |
3days |
10hrs |
2days |
8hrs |
1days |
|
|
Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Yacht Line Super Cleaner, rinse
with fresh water and allow to dry. Abrade with 280-320 grade (grit)
paper.
In Poor Condition: Remove all previous coatings and prime the
substrate.
PRIMING: All preparation for bare substrates is covered on the
appropriate primer datasheet.
BARE WOOD: Prime with UCP.
STEEL: Prime with Interprotect.
ALUMINIUM: Pre-prime using Etch Primer. Prime with Interprotect.
GRP: Wash down with Yacht Line Super Cleaner, rinse with fresh
water and allow to dry. Abrade with 180-220 grade paper.
ALL SUBSTRATES: If any filling is required use the appropriate
product from the Interfill range. |
|
|
|
Method |
If maximum overcoating time of previous coating/primer is exceeded,
abrade using 180-220 grade paper. Remove dust with a dust wipe. Apply
1-2 coats. |
|
|
|
Hints |
Mixing Stir contents of each part prior to mixing. Add Curing
Agent to the Base, stir and leave for 10 minutes to allow bubbles to
disperse.
Thinner YTA006 Thinners No.9
Cleaner YTA006 Thinners No.9
Ventilation and Humidity Control Apply in dry, well ventilated
conditions. Avoid excessively humid conditions, over 80% relative
humidity.
Other Best applied at 15°C. To give extra depth of colour,
Perfection finish colours may be added to Perfection Undercoat. Both
products should be mixed with respective curing agent first. |
|
|
|
Some Important Points |
Do not use unless mixed thoroughly with the curing agent at specified
ratio. Product temperature should be minimum 5°C/40°F and maximum
35°C/95°F. Ambient temperature should be minimum 5°C/40°F and maximum
35°C/95°F. Substrate temperature should be minimum 5°C/40°F and maximum
35°C/95°F. |
|
|
|
Compatibility/Substrates |
Will crack on carvel and clinker/lapstrake hulls. Perfection Undercoat
should be applied over cured epoxy primers or fillers or onto cured GRP/Composite.
It should not be used over any one pack products. |
|
|
|
Number of Coats |
1-2 |
|
|
|
Coverage |
(Theoretical) - 12.00 (m²/lt) |
|
|
|
Recommended DFT |
38 microns dry by brush
|
|
Recommended WFT |
75 microns wet by brush |
|
|
|
Application Methods |
Brush, Roller , DO NOT SPRAY |
|
|
Storage |
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Perfection Undercoat to be realised ensure that
between use the container is firmly closed and the temperature is
between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection Undercoat should be kept in securely closed containers during
transport and storage.
|
|
|
|
Safety |
GENERAL: Contains isocyanates which may be harmful to the respiratory
tract. Read the label safety section for Health and Safety Information,
also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Perfection Undercoat cannot be disposed of through the
municipal waste route or dumped without permit. Disposal of remainders
must be arranged for in consultation with the authorities.
|
|
|
IMPORTANT NOTES |
The information given in this sheet is not intended to be exhaustive.
Any person using the product without first making further written
enquiries as to the suitability of the product for the intended purpose
does so at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
 and
International are registered trademarks of Akzo Nobel. |
|
