Perfection 2-part polyurethane is the ultimate performing, high gloss
topside finish. It provides the longest-lasting, ultra-high gloss finish
that has superb colour-retention, together with excellent chemical and
abrasion resistance. It has been formulated specifically to enable
skilled amateur users to achieve professional-quality results with ease.
UV filters combined with the chemical cure of the polyurethane to give
the longest life possible.
* Hardest, abrasion-resistant finish making it an excellent choice for
use on high wear areas e.g. decks (with Intergrip additive).
* Chemically resistant to diesel, petrol, oil, mild acids and alkalis |
|
|
Colour |
YHA183-Platinum A183, YHA184-Mediterranean White A184, YHA192-Off White
A192, YHA194-Oyster White A194, YHA198-Matterhorn White A198,
YHA216-Royal Blue A216, YHB000-Snow White B000, YHB663-Jade Mist Green
B663, YHE294-Chilli Red, YHF991-Mauritius Blue F991, YHK990-Flag Blue
K990, YHS056-Fighting Lady Yellow S056, YHS070-Cream S070,
YHS299-Rochelle Red S299, YHY999-Jet Black Y999 |
|
Finish |
High Gloss |
|
Specific Gravity |
1.167 |
|
Volume Solids |
49.0% |
|
Mix Ratio |
2:1 by volume (as supplied) , Converter/Curing Agent - YGB001 |
|
Typical Shelf Life |
2 yrs |
|
VOC (As Supplied) |
486 g/lt |
|
Unit Size |
750 ml 2.5 Lt (some colours only) |
|
|
| |
Drying |
|
5ºC |
15ºC |
23ºC |
35ºC |
|
|
|
Touch Dry [ISO] |
11hrs |
7hrs |
4hrs |
3hrs |
|
Pot Life |
5hrs |
3hrs |
2hrs |
1hrs |
| |
Overcoating |
| |
Substrate Temperature |
| |
5ºC |
15ºC |
23ºC |
35ºC |
|
Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
|
Perfection |
28hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Yacht Line Super Cleaner, rinse
with fresh water and allow to dry. Abrade with 280-320 grade (grit)
paper.
In Poor Condition: Remove all previous coatings and prime the
substrate.
PRIMING: All preparation for bare substrates is covered on the
appropriate primer datasheet.
BARE WOOD: Prime with UCP or Interprotect.
STEEL: Prime with Interprotect.
ALUMINIUM: Pre-prime using Etch Primer. Prime with Interprotect.
GRP: Wash down with Yacht Line Super Cleaner, rinse with fresh
water and allow to dry. Sweep blast or abrade with 180-220 grade paper.
No priming necessary.
AGED/WEATHERED GELCOATS: Due to the potentially porous nature of
aged/weathered gelcoats the risk of solvent/moisture entrapment after
painting is much higher than when gelcoat is new. As a result this
entrapment could lead to blistering of the paint film. To reduce the
risk of paint film blistering it is recommended that 3 coats of
Interprotect are applied to seal the gelcoat. Interprotect must be
overcoated with Perfection Undercoat prior to topcoat application.
ALL SUBSTRATES: Use Perfection Undercoat.
|
|
|
|
Method |
Sand the undercoat smooth with 320-400 grade (grit) wet or dry paper.
Remove dust with a tack rag. Apply 2-3 coats. |
|
|
|
Hints |
Mixing Stir contents of each part prior to mixing. Add Curing
Agent to the Base, stir and leave for 20 minutes to allow bubbles to
disperse.
Thinner YTA006 International Retarder Thinners #9.
Cleaner YTA006 International Retarder Thinners #9.
Ventilation and Humidity Control Apply in dry, well ventilated
conditions. Avoid excessively humid conditions, over 80% relative
humidity.
Other Best applied at 15°C. For lighter colors, mix the first
coat of finish 50:50 with the undercoat to improve the depth of color
and opacity. Both products should be mixed with respective curing agents
first. For best results when applying by roller, smooth off with a pad
or brush. If using as a deck paint, mix in non-slip additive. Full
hardness is achieved after 7-10 days at 15°C/59°F. If required,
Perfection Matting Additive (YZM914) is available for use with
Perfection. See Perfection Matting Additive datasheet for details on
use. |
|
|
|
Some Important Points |
Do not use unless mixed thoroughly with the curing agent at specified
ratio. Avoid painting in direct sunlight. Avoid applying late in the
evening as condensation can cause a loss of gloss during overnight cure.
Allow to dry in a well ventilated environment. Product temperature
should be minimum 15°C/59°F and maximum 35°C/95°F. Ambient temperature
should be minimum 5°C/40°F and maximum 30°C/86°F. Substrate temperature
should be minimum 5°C/40°F and maximum 30°C/86°F. |
|
|
|
Compatibility/Substrates |
Do not use Perfection on flexible constructions. Will crack on carvel
and clinker/lapstrake hulls. Perfection should not be used over any
one-pack products. Not suitable for permanently immersed surfaces. |
|
|
|
Number of Coats |
2-3 |
|
|
|
Coverage |
(Theoretical) - 12.00 (m²/lt) |
|
|
|
Recommended DFT |
37 microns dry
|
|
Recommended WFT |
75 microns wet |
|
|
|
Application Methods |
Brush, Roller , DO NOT SPRAY |
|
|
Storage |
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of this product to be realised ensure that between use
the container is firmly closed and the temperature is between 5°C/40°F
and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection should be kept in securely closed containers during transport
and storage.
|
|
|
|
Safety |
GENERAL: Contains isocyanates which may be harmful to the respiratory
tract. Read the label safety section for Health and Safety Information,
also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Perfection cannot be disposed of through the municipal
waste route or dumped without permit. Disposal of remainders must be
arranged for in consultation with the authorities.
|
|
|
IMPORTANT NOTES |
The information given in this sheet is not intended to be exhaustive.
Any person using the product without first making further written
enquiries as to the suitability of the product for the intended purpose
does so at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
 and
International are registered trademarks of Akzo Nobel. |
|
