|
A traditional yacht varnish with UV resistance. Features include
excellent flexibility, ease of application, good gloss retention, and
non-blooming qualities. A high clarity finish especially suited to
lighter colour timbers. |
|
|
Colour |
YVA202-Clear |
|
Finish |
Full gloss |
|
Specific Gravity |
0.93 |
|
Volume Solids |
52% |
|
Typical Shelf Life |
2 yrs |
|
VOC (As Supplied) |
352 g/lt |
|
Unit Size |
375 ml 750 ml 2.5 Lt |
|
| |
Drying |
|
5ºC |
15ºC |
23ºC |
35ºC |
|
|
|
Touch Dry [ISO] |
16hrs |
10hrs |
5hrs |
3hrs |
| |
Overcoating |
| |
Substrate Temperature |
| |
5ºC |
15ºC |
23ºC |
35ºC |
|
Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
|
Original |
36hrs |
5days |
24hrs |
4days |
16hrs |
2days |
12hrs |
1days |
|
|
Preparation |
PREVIOUSLY VARNISHED WOOD:
In Good Condition: Clean with thinners. Sand smooth with 280-320
grade paper. Remove sanding dust with thinners.
In Poor Condition: Remove all previous coatings.
BARE WOOD: Sand smooth with 80-180 grade paper and then 280 grade
paper. Remove sanding dust by brushing, dusting and wiping. If wiping
with solvent then allow to dry completely before applying the first
coat.
Priming bare wood:: Apply Intertox or UCP. If UCP has been
omitted thin the first coat by 10-15% with Thinners No.1. |
|
|
|
Method |
Apply a minimum of 3 unthinned coats, more if using a roller. |
|
|
|
Hints |
Mixing Stir well before use.
Thinner YTA800,YTA085 Thinners No.1 Thinners No.3
Cleaner YTA800 Thinners No.1
Airless Spray Pressure: 176-210 bar. Tip Size: 1365-1580.
Conventional Spray Pressure: 2-3 bar. Tip Size: 1.1-1.4 mm. Thin
25-30% with Thinners No.3
Roller If applying by roller, lay off with a brush or pad
otherwise air bubbles may become trapped in the film.
Other For Airmix spray application: Pressure: 2 bar. Tip Size:
06-113. For best results sand lightly between coats with 320-400 grade
paper. Avoid using direct from the can. Pour the amount you expect to
use in a separate container. |
|
|
|
Some Important Points |
Use above the waterline only. Do not use below 5°C. Avoid painting in
direct sunlight. Product temperature should be minimum 15°C and maximum
35°C. Ambient temperature should be minimum 5°C/40°F and maximum
35°C/95°F. Substrate temperature should be minimum 5°C/40°F and maximum
35°C/95°F. |
|
|
|
Compatibility/Substrates |
Suitable for use on all types of wood except direct application on oily
timbers such as Teak and Iroko. |
|
|
|
Number of Coats |
3 minimum |
|
|
|
Coverage |
(Theoretical) - 11.70 (m²/lt) |
|
|
|
Recommended DFT |
40 microns dry by brush
|
|
Recommended WFT |
77 microns wet by brush |
|
|
|
Application Methods |
Brush, Roller, Conventional Spray, Airmix, Airless Spray |
|
|
Storage |
GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Original to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Original should be kept in securely closed containers during transport
and storage.
|
|
|
|
Safety |
GENERAL: Read the label safety section for Health and Safety
Information, also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Original cannot be disposed of through the municipal waste
route or dumped without permit. Disposal of remainders must be arranged
for in consultation with the authorities.
|
|
|
IMPORTANT NOTES |
The information given in this sheet is not intended to be exhaustive.
Any person using the product without first making further written
enquiries as to the suitability of the product for the intended purpose
does so at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
 and
International are registered trademarks of Akzo Nobel. |
|
